DODGE DAKOTA FORUM - FORUM AND OWNERS CLUB! - Reply to Topic
DODGE DAKOTA FORUM - FORUM AND OWNERS CLUB!  

Go Back   DODGE DAKOTA FORUM - FORUM AND OWNERS CLUB! > DODGE DAKOTA FORUM - Mod Zone - Custom Dodge Dakota Mods - Dodge Dakota Performance > Computers and Powertrain Control Modules > '98 3.9 computer.
Dodge Ram Dodge Durango Dodge Nitro Jeep
Diesel Forums!
Dodge Ram Forum Dodge Durango Forum Dodge Nitro Forum Jeep Forum
Dodge Challenger Dodge Charger Chrysler 300 Dodge Magnum
Dodge Caliber
Dodge Challenger Forum Dodge Charger Forum Chrysler 300 Forum Dodge Magnum Forum


Notices

Thread: '98 3.9 computer. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the DODGE DAKOTA FORUM - FORUM AND OWNERS CLUB! forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address

Please enter a valid email address for yourself.

Note: If your email address requires someone to click a link before they can send you email, DO NOT REGISTER WITH IT as no one is here to click the link and you will never get your activation email!
We have banned MANY Free email providers.
If you get notice that your email address is banned when you try to sign up, it is because its been banned due to spammers using the provider, or too many members bouncing emails we send back to us via the free provider! If this happens to you, you will need to use a different email. If you do not provide a valid email address you will not receive your activation email. We recommend that you register with an email address which is attached to your ISP! Not a free service! We have found that using free accounts causes you to not receive your registration email. In any case, you should add DakotaForumZ.com to your spam filter whether using a free account or your ISP account. If you bounce email to us, you will have your account deleted and your IP address banned!

Email Address:
Vehicle
Enter the model year and make of your vehicle! (I.E. 2000 Dodge Dakota)
Engine
Please select your engine so that members will be better able to answer questions you ask on the forum! This shows up on your profile page!
Insurance
Please select your insurance company (Optional)
Color
What color is your vehicle?
Trim Level
What trim level did you purchase?

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-17-2019 11:45 PM
RalphP
Quote:
Originally Posted by immattj View Post
Is this ground you are alluding to an internal ground inside the computer? Or is it one of the wires of the bundle that is in the main connector to the computer?


Did OP ever fix his problem & if so, what was it?
It could be almost ANY ground on the truck; but usually not only where the computer grounds to the chassis, but also where the negative cable grounds to the block and/or the chassis, or any or all of the above!

RwP
10-17-2019 11:14 PM
immattj Is this ground you are alluding to an internal ground inside the computer? Or is it one of the wires of the bundle that is in the main connector to the computer?


Did OP ever fix his problem & if so, what was it?
10-16-2019 03:16 PM
ASEDodgeDude Very good point Jaycee. Loose or dirty grounds can cause all sorts of gremlins. As the PCM grounds everything it switches on and off a good ground is imperative.
10-15-2019 09:11 PM
jaycee I had the same issue with my 05. They say the ground from the computer had come loose. They tightened it up and I have not had an issues since.
09-26-2019 09:27 PM
immattj I had a similar issue; however mine is a '03 with a 5.9.

So keeping that in mind, when mine was in the "crank but not starting mode", I was not getting voltage from the coil when cranking. While this issue was intermittent, I changed a bunch of parts; however, this issue devolved from being intermittent to being a permanent no start condition.
(Which is easier to troubleshoot.)
Keeping that in mind, & shortening the rest of my story, the rest of my troubleshooting ended in not getting voltage at the trigger wire (when cranking) from the PCM to the coil (which on mine is a black wire w/ white stripe), as evidenced by back probing trigger wire with a test light & not observing it flashing (when cranking).
I realize that your issue is resolving itself almost immediately, so that makes it harder to troubleshoot.
However, if your issue devolves as mine did, if you get no voltage from your trigger wire to coil, the troubleshooting tree I followed drove me next to the ASD relay (which I had already swapped) & then to the PCM.


I am going to plug SIA Electronics in (I believe) Tilden Il., simply because they solved my problem. I contacted them & sent them my PCM. I cannot remember what the bill was, but I remember it being under $150.00. They told me they replaced the "coil transistor" & "resoldered a loose pin". They do have a fee for checking & finding no defects & shipping back, but I cannot remember how much it is, but it is probably on their web site.
So I'm just throwing that out there for you in case that's what your issue turns out to be, as they solved mine.


I tend to doubt your problem is your coil. My admittedly limited experience has been that coils either work or they don't. But I would think that you could get a coil from RockAuto.com pretty affordably if you want to do that as a check, & even if it doesn't work, at least you will always have a spare coil. (That's the rational I am holding on to for my extra relays, cam pos sensor, & crank pos sensor I now own).


I hope you post the resolution to your issue for the future reference to us all.
Good luck!
09-20-2019 05:55 PM
oldmarine In the 2000 FSM, and I think the 1999 is the same, the ASD relay is right next to the Fuel Pump relay - between the Fuel Pump relay and fuse #2.
09-20-2019 05:37 AM
oldsfan1 [QUOTE=oldsfan1;41293]Thanks for your help. The issue is most of the time it starts imminently up with all systems working properly with everything getting power. I think changing the coil might be next. Now what about the computer, can a salvage computer be used without a dealer reset. I hope I don't need to replace the (pcm). Anyone used any of the send your pcm in and we will repair and reset your computer guys that are on line. I hate this "try and part one at a time" stuff. I tried Rock Auto and can't find a pcm,computer listing. Thanks for your suggestions and help.[/QUO

I have replaced the fuel pump relay..is that the ASD relay Auto Shut Down Relay...if not the fuel pump relay where is the ASD relay located?
Again thanks
09-20-2019 05:23 AM
oldsfan1 Thanks for your help. The issue is most of the time it starts imminently up with all systems working properly with everything getting power. I think changing the coil might be next. Now what about the computer, can a salvage computer be used without a dealer reset. I hope I don't need to replace the (pcm). Anyone used any of the send your pcm in and we will repair and reset your computer guys that are on line. I hate this "try and part one at a time" stuff. I tried Rock Auto and can't find a pcm,computer listing. Thanks for your suggestions and help.
09-20-2019 05:15 AM
oldsfan1
Quote:
Originally Posted by ASEDodgeDude View Post
When you have the no start, check for grounding at the injectors. A cheap test light can be used. Find the injector plug and probe with switch on. The one that stays lit is the power. Go to other wire and have someone crank it over. This is the ground side, which the pcm controls.you should se the light flash.if not your pcm is not firing the injectors. Doesn't mean bad pcm tho. Check ASD relay. Swap another relay and see if problem goes away. Check voltage to sensors, TPS, IAC, ect. Should see 5v on a wire of each sensor. This will verify comp is providing reference voltage. Coil can do it also, but I believe the problem is elsewhere. Check the basics...when it no starts. Do you have spark? Do you have injector pulse? Find out what's missing and it'll lead you to the problem
Thanks for your help.
09-19-2019 03:41 PM
ASEDodgeDude When you have the no start, check for grounding at the injectors. A cheap test light can be used. Find the injector plug and probe with switch on. The one that stays lit is the power. Go to other wire and have someone crank it over. This is the ground side, which the pcm controls.you should se the light flash.if not your pcm is not firing the injectors. Doesn't mean bad pcm tho. Check ASD relay. Swap another relay and see if problem goes away. Check voltage to sensors, TPS, IAC, ect. Should see 5v on a wire of each sensor. This will verify comp is providing reference voltage. Coil can do it also, but I believe the problem is elsewhere. Check the basics...when it no starts. Do you have spark? Do you have injector pulse? Find out what's missing and it'll lead you to the problem
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


» Advertisement



All times are GMT. The time now is 12:21 AM.


Powered by vBulletin® Version 3.8.10 Beta 2
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vB.Sponsors
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright © VerticalScope Inc. All rights reserved.